Quadcopter High Altitude ESC and Motor Failure

1490074469_hqdefault.jpg




Rear left ESC fails then right front motor overheats and fails (assumming it overheated when trying to yaw compensate for the motor attached to the failed ESC)
A look at the frame: https://downanddirtydrones.com/portfolio/

Sunnysky 2300kv
4S 1300mah
SJ4000 Cam
RunCam PZ0420M FPV Cam
Immersion Video Tx
5030 Props
ZTW Mantis 12a ESC’s
CC3D FC

source

Quadcopter High Altitude ESC and Motor Failure

1490074469_hqdefault.jpg




Rear left ESC fails then right front motor overheats and fails (assumming it overheated when trying to yaw compensate for the motor attached to the failed ESC)
A look at the frame: https://downanddirtydrones.com/portfolio/

Sunnysky 2300kv
4S 1300mah
SJ4000 Cam
RunCam PZ0420M FPV Cam
Immersion Video Tx
5030 Props
ZTW Mantis 12a ESC’s
CC3D FC

source

KK2.1 DIY Wooden H 680 Quadcopter Build Part 3. Install ESC and TEST Flight

1477292156_hqdefault.jpg




Final Build video of my DIY Wooden Quadcopter.

Motors $12 EBAY Special
ESCs $30 EBAY
KK2.1HC $30 Hobbyking
Wire $4
Timber $8

Total $84

Might be my cheapest build yet.

source

Alien X FPV Quadcopter part two Motor and Esc Soldering

1448980076_hqdefault.jpg




Στο δεύτερο βίντεο περιγράφω τη διαδικασία προετοιμασίας και τοποθέτησης των Banana Connector plug 3.5 mm με σύρμα κόλλησης(καλάι) στα μοτέρ αλλά και στους speed controllers.

http://myquadcopter.gr/

source

ZMR250 Quadcopter – Soldering ESCs to PDB

1444450223_hqdefault.jpg




In this video I show the steps involved in performing the final cuts and soldering of the ESC wiring onto the PDB, and I discuss the next steps involving the Flight Controller board, Naze32. Thanks for watching! Please hit “LIKE” and SUBSCRIBE for more Videos!

source

Hobbyking Diatone 250 Quadcopter build with DYS 2300kv motors 12A Afro ESC KK2.1 RC911 Turnigy 9x

1438727020_hqdefault.jpg




Next Project

Trying to make a small, fast, very responsive ACRO Quadcopter.
Here is the Build.

Hobbyking 250 ACRO Quad

Trying out the mini quad experience using Hobbyking Parts.

HK 250 Diatone Frame
DSY 1806 2300kV Motors
AFRO 12a ESCs
KK2,1 Flight Controller using RC911 Firmware
Turnigy 9x Transmitter and Receiver

See the PI settings here

See the Flight Demonstration here.


source

750 long duration Endurance Quadcopter with Naza V2 Rctimer 5010 360kv Afro Slim ESC Talon V2

1433660718_hqdefault.jpg




This is a long duration quadcopter. The flight time with these two 5000Mah Turnigy 20-30C batteries lasted over 40 minutes. This is the first test of this quad. I will be testing two 7200 Mah batteries next and I will be getting over 50 minutes with this setup. I still have to add a video tx and my choice of camera and then this quad will be set for fpv. The ESC’s seem to be staying pretty cool for being 20amp. The parts used in this build are as follows:
Frame: Talon v2 with extended arms to make it a Talon v2 750. Motor mount holes need to be drilled to fit the c-clip on the motors.
Naza V2 Controller with GPS
20A Slim Afro Escs (SimonK)
17×5.5 CF Rctimer props
Turnigy 5000Mah 4s 20-30C will run 2 in parallel. Will also change these out for Turnigy 7200Mah 40-80C depending on desired flight.
RcTimer 5010 360kv motors
L9r Receiver
Transmitter Frsky Taranis
I am now in the process of building a Tarot FY690 Hexacopter that will be used for high quality aerial videography.

Filmed By: Jordan Mowbray

source