Flysky FS-i6S PPM & iBUS Setup


Tutorial video on how to setup PPM and iBus on the Flysky FS-i6S for Cleanflight (or Betaflight) flight controllers.

Check out the Flysky radio here –

RunCam2 –
Xiaomi Yi Action Camera –
FrSky Taranis X9D Plus –
Fatshark Dominator V3 Goggles –

What I use to edit my videos –
What I use to film my videos –





Please consider supporting me on Patreon:

If your Cleanflight or Betaflight quadcopter won’t arm, there’s a relatively short list of possible causes. I’ll take you through all the possible things that could be preventing your quadcopter from arming, so that you can find the one that’s affecting you, fix it, and get into the air!


GoolRC G90 Cheap F3 EVO Micro FPV Racing Drone Flight Test Review


This little quadcopter might be for you if you’re Looking for an inexpensive but great performing micro FPV racer. Buy the GoolRC G90 here (only available for Frsky)

– Great flier out of the box. Fast little quad with 8520 brushed micro.
– F3 EVO flight control board loaded with CF SPRACINGF3 1.13.0
– 800TVL 40 channel, 25 mW all in one FPV camera.
– As this is a small micro, you can safely fly this just about anywhere (even indoors).
– Probably one of the least expensive micro FPV racers that you can currently find with a configurable FCB. Likely cheaper than you can build yourself.
– Does not require FAA registration.

– Currently only available for Frsky
– Video reception was perfect on my VR01 goggles, but scratchy on the recorded video from the VRD2 goggles. The quadcopters FPV antenna was “bent” out of the box. I’m thinking that I probably should have straghtened it out 😉
– Motor leads are soldered to the FCB. Wire splicing is recommended if you need to change a motor.

Affiliate links: At no cost to you, I do receive a small commission for sales resulting from these links.

This video along with every video of the Quadcopter 101 channel was produced and edited with VSDC Free Video Editor. You may download this excellent, and no kidding “free” video editor here

“Awel” by stefsax
is licensed under a Creative Commons license:
music was shortened to fit length of video.


Makerfire Micro FPV Drohne / Quadcopter von // Testbericht & Testflug


Mein Review zur genialen Makerfire Micro FPV Drohne, erhältlich bei Gearbest:

Daten & Infos
Flugzeit ca 5 Minuten, Ladezeit ca. 25-30 Minuten, Reichweite der Fernbedienung ca 1500m / FPV Empfang bis 300 Meter

Link zur Fernsteuerung MKron T-Six:
Passende FuriBee FPV Brille:

Mehr von unseren Videos? Dann abonniere unseren Kanal und gib einen Daumen hoch.

Social Media



TeknoAxe – Urban Jungle Intro Bits
TeknoAxe – I`m Everywhere Intro Bits


Funny Compilation of epic drone crashes!


Short Compilation Of some random crashes with my custom VrS 220 Racing drone.


Build Along QAV X // PART 2 // Setup Betaflight for Multi-Purpose Quadcopter Bundle


IMPORTANT! Remove props before you do anything instructed in this video. I forgot to mention this in the start. It’s really important to remove your props

Interested in building this quad? Purchase this kit here:


Betaflight Configurator:

BlHeli Configurator:

Betaflight Firmware:

In this video I’ll be going over the setup process in Betalfight and the BlHeli Configurator for the Multi-Purpose FPV Quadcopter. If you’re looking for a really high-performance FPV Quad then look no further. This quadcopter packs a serious punch! The components are on par with what most Professional FPV Pilots are flying. If you are new to FPV, this quad will be perfect for a beginner pilot since it will take a beating against whatever you throw it at. At the same time, it’ll have all the performance you need when progressing as a pilot.

This is the exact same quadcopter that Jack will be using for all How-to videos on the channel. Jack will also be racing this quadcopter at National and International events.

Want Premium FPV Flying and Technical support? Checkout the FPV Pilot Support Program!

FPV Pilot Support Program:

Stay in touch!


Build Along QAV X // PART 2 // Setup Betaflight for Multi-Purpose Quadcopter Bundle
Build Along QAV X // PART 2 // Setup Betaflight for Multi-Purpose Quadcopter Bundle
Build Along QAV X // PART 2 // Setup Betaflight for Multi-Purpose Quadcopter Bundle


Tiny Whoop Mini FPV Racing Quadcopter Clone


The Tiny Whoop is a popular FPV racing drone and costs $100. The Eachine Turbine QX70 FPV racing quadcopter is less than $75, uses a standard 2 pin 1S LiPo, and costs around $70.
To buy Eachine Turbine FPV Mini Racer:

This video shows the Eachine Turbine QX70 FPV racing quadcopter in action. We also show you the basic configuration to use in Cleanflight before you fly.


92MM Micro FPV Racing RC Quadcopter Frame Kit Based On SP RACING F3_EVO_Brush Flight controller



300mah 2S lipo from hobbyking
Orange satellite.

40g with out lipo.

ignore the date on the video, date not set on the DVR


Betaflight 2.9.0//PID Tuning//3S(11.1V) Test//SPRacing F3 QAV210 Sunset Drone GoPro FPV//Cleanflight


Recommended parts are as follows.
QAV210 with SPRacing F3 Kit
Motor : Emax 2205 2300KV
FC : SPRacing F3 (4khz/2khz)
Battery : 3S (11.1V)
Props : DYS 5x4x3
FPV Goggle (Fatshark Predator v2)
Video TX (TS5828 5.8G 32CH)
3S Lipo Charger (iMax B3)
Firmware : Betaflight 2.9.0 (Boris B)

This firmware is very smooth.
It gives me awsome flight.
It’s very fun!!

Details of Betaflight 2.9.0

Amazing flight!! (Betaflight 2.9.0)

Amazing flight!! (Betaflight 3.0)

GoPro HERO4 Black Edition

GoPro HERO5 Black

GoPro Battery

SPRacing F3 10DOF(Drone flight controller)

Davinci Resolve

Fatshark Dominator HD V2(FPV goggle)

Fatshark Dominator V3(FPV goggle)

About Drone (DJI Phantom4,GoPro Karma)

blheli,blheli_s,gopro hero,blackbox,pid tuning,rate,sunset,drone fly,drone of the day,littlebee,passthrough,set up,2.9.0,2.9.1,3.0.0,cc3d,naze32,Fatshark,mpc,
RC,Parrot,AR,Drone,fpv,osd,remote,wifi,camera,system,goggles,plane,video,helicoptor,long range,quadcoptor,equipment,fly,quad,flight,buy,best,hd,transmitter,hubsan,lunette,ecran,immersion,
Alabama,Alaska,Arizona,Arkansas,California,Colorado,Connecticut,Delaware,Florida,Georgia,Hawaii,Idaho,Illinois,Indiana,Iowa,Kansas,Kentuckey,Louisiana,Maine,Maryland,Massachusetts,Michigan,Minnesota,Mississippi,Missouri,Montana,Nebraska,Nevada,New Hampshire,New Jersey,New Mexico,New York,North Carolina,North Dakota,Ohio,Oklahoma,Oregon,Pennsylvania,Rhode Island,South Carolina,South Dakota,Tennessee,Texas,Utah,Vermont,Verginia,Washington,West Verginia,Wisconsin,Wyoming,District of Columbia,Puerto Rico


Quadcopter RGB LED wiring and setup in cleanflight

1482968534_hqdefault.jpg explains how to connect an RGB LED to a naze32 Acro Rev 6 board running Cleanflight. You can get this LED board here: There is an included wiring diagram and cleanflight setup instructions in this video. We hope it helps! Please post your Quad Questions at and we might select yours as the topic for our next video.